To test network resolution, use the host name instead of the IP address. If there is no DNS server on the network, /etc/hosts must first be configured. To this purpose, edit /etc/hosts to add the names and IP addresses of the hosts on the LAN, if they are not already there. Ghost Solution Suite Agent (DAgent and ADLAgent): Agents require network connectivity and 10 MB of disk space. Other system requirements are the same as for the host operating system. Other system requirements are the same as for the host operating system. Poser - aery soul 77 files. I have a project that I want to test before I do this on a large scale and it involves Norton Ghost 8.3 Corp. I know it is possible to push ghost images over the network however I have not been able to acomplish this. Right now I have a share folder on the network where I store all the ghost images. I want to be able to boot into a machine using Norton Ghost and select an image from the share folder of another machine have it image the HD. I would like a step by step instruction on this procedure. Thank you very much!! Yes from the command line A: > you will need to go over and over the command (entire line) until you get it right I made one, that took ages until I now have it working all the time (but this is specific to networks, name of image, location, etc. You need to check each part of the command until you get it right. You can also add this to your autoexec.bat file (the boot up command file) The main part of all this is to have the right DOS network drivers. That's why I made a CD, I put hundreds of network drivers on it! Good luck, you are starting on a tad higher level than basic Ghost commands, so you may have some issues until it works. The ghost floppy that you have made must not have the command interpretter $p$g inside command.com (or is it io.sys) anyway, you may need to download another boot disk (try ) and copy ghost to a folder inside A drive called ghost. Ie A: GHOST Ghost.exe To use ghost, just CD to GHOST folder and run Ghost ie A:/>CD GHOST then type ghost to start it Hopefully you should have an A prompt on exit as well Also have you tried F (Fail) the F (Fail) then type B: Sometimes the floppy is set for B: not A: (such as on a bootcd). Why are you distributing your ghost images using this method? The easiest way is to use GhostCast Server - which is included on your Ghost Corp CD. You don't even have to do any additional registering for it unless you use the Ghost Console. If you use the ghost server you simple start up a server session - select which image you want to send out, you can tell it how many clients to expect or just have it wait till you say ready, and then have all your clients locate the waiting server. You also don't have to create any shared folders using this method. After following all the instructions on this site and I am pretty sure I've loaded the correct network driver. I receive the following error stating: Unable to locate the NIC 1. ![]() The system may not support the PCI Bus 2. The NIC may not be properly installed in a slot 3. Some of the NIC resources in configuration may be involved. Where can I download dos drivers for NICS? I am trying to re-image the HD of a SuperMicro PDSBM-LN2+ motherboard. Cosmopolitan philippines magazine pdf free download. I am using this as my test machine, I've already successfully installed Win2kPro on the server using the standard method. Used ghost to create of image and save the image on a different server. Wipe the HD clean on the SuperMicro and now I want to push the image back. You're getting there. Asking for DOS drivers for your NIC means you know stuff now Anyway, you will need to confirm what network card you have. The make and model. Overrated I can't think of any benefit from walking over riding other than I enjoy walking more. I my case It is much more peaceful so I think it helps me focus more on the next shot. Golf digest hot list 2004 drivers. My particular course ends up being cart path only when wet so it actually works out better being able to walk because I have all my clubs right there with me instead of trying to guess which ones I need as I walk across the fairway to my ball. I also think it has something to do with just being able to walk (living in Florida) because their are so fun places that you are allowed to walk or it becomes just too hot in the summer. This info is stamped on the card somewhere, or it's in your motherboard manual (you can download this online) from your computers motherboard support page. Once you know the name and model number of your NIC, you then search the manufacture website for the DOS network drivers. If they don't supply them, then that's when Google comes in. Download the drivers (eventually) extract them, and add them to the Ghost Network installation. Why are you distributing your ghost images using this method? The easiest way is to use GhostCast Server - which is included on your Ghost Corp CD. You don't even have to do any additional registering for it unless you use the Ghost Console.
0 Comments
Leave a Reply. |